ELECTRICAL ENGINEERING TOP INTERVIEW QUESTION & ANSWER

                          ELECTRICAL ENGINEER 

Electrical Engineering interview questions and answers  Why star delta starter is preferred with induction motor? Star delta starter is preferred with induction motor due to following reasons: • Starting current is reduced 3-4 times of the direct current due to which voltage drops and hence it causes less losses. • Star delta starter circuit comes in circuit first during starting of motor, which reduces voltage 3 times, that is why current also reduces up to 3 times and hence less motor burning is caused. • In addition, starting torque is increased and it prevents the damage of motor winding. State the difference between generator and alternator Generator and alternator are two devices, which converts mechanical energy into electrical energy. Both have the same principle of electromagnetic induction, the only difference is that their construction. Generator persists stationary magnetic field and rotating conductor which rolls on the armature with slip rings and brushes riding against each other, hence it converts the induced emf into dc current for external load whereas an alternator has a stationary armature and rotating magnetic field for high voltages but for low voltage output rotating armature and stationary magnetic field is used. Why AC systems are preferred over DC systems? Due to following reasons, AC systems are preferred over DC systems: a. It is easy to maintain and change the voltage of AC electricity for transmission and distribution. b. Plant cost for AC transmission (circuit breakers, transformers etc) is much lower than the equivalent DC transmission c. From power stations, AC is produced so it is better to use AC then DC instead of converting it. d. When a large fault occurs in a network, it is easier to interrupt in an AC system, as the sine wave current will naturally tend to zero at some point making the current easier to interrupt. How can you relate power engineering with electrical engineering? Power engineering is a sub division of electrical engineering. It deals with generation, transmission and distribution of energy in electrical form. Design of all power equipments also comes under power engineering. Power engineers may work on the design and maintenance of the power grid i.e. called on grid systems and they might work on off grid systems that are not connected to the system. What are the various kind of cables used for transmission? Cables, which are used for transmitting power, can be categorized in three forms: • Low-tension cables, which can transmit voltage upto 1000 volts. • High-tension cables can transmit voltage upto 23000 volts. • Super tension cables can transmit voltage 66 kV to 132 kV. Why back emf used for a dc motor? highlight its significance. The induced emf developed when the rotating conductors of the armature between the poles of magnet, in a DC motor, cut the magnetic flux, opposes the current flowing through the conductor, when the armature rotates, is called back emf. Its value depends upon the speed of rotation of the armature conductors. In starting, the value of back emf is zero. What is slip in an induction motor? Slip can be defined as the difference between the flux speed (Ns) and the rotor speed (N). Speed of the rotor of an induction motor is always less than its synchronous speed. It is usually expressed as a percentage of synchronous speed (Ns) and represented by the symbol ‘S’. Explain the application of storage batteries. Storage batteries are used for various purposes, some of the applications are mentioned below: • For the operation of protective devices and for emergency lighting at generating stations and substations. • For starting, ignition and lighting of automobiles, aircrafts etc. • For lighting on steam and diesel railways trains. • As a supply power source in telephone exchange, laboratories and broad casting stations. • For emergency lighting at hospitals, banks, rural areas where electricity supplies are not possible. 10. What are the different methods for the starting of a synchronous motor. Starting methods: Synchronous motor can be started by the following two methods: • By means of an auxiliary motor: The rotor of a synchronous motor is rotated by auxiliary motor. Then rotor poles are excited due to which the rotor field is locked with the stator-revolving field and continuous rotation is obtained. • By providing damper winding: Here, bar conductors are embedded in the outer periphery of the rotor poles and are short-circuited with the short-circuiting rings at both sides. The machine is started as a squirrel cage induction motor first. When it picks up speed, excitation is given to the rotor and the rotor starts rotating continuously as the rotor field is locked with stator revolving field. 11. Name the types of motors used in vacuum cleaners, phonographic appliances, vending machines, refrigerators, rolling mills, lathes, power factor improvement and cranes. Following motors are used: - • Vacuum cleaners- Universal motor. • Phonographic appliances – Hysteresis motor. • Vending machines – Shaded pole motor. • Refrigerators – Capacitor split phase motors. • Rolling mills – Cumulative motors. • Lathes – DC shunt motors. • Power factor improvement – Synchronous motors. 12. State Thevenin’s Theorem: According to thevenin’s theorem, the current flowing through a load resistance Connected across any two terminals of a linear active bilateral network is the ratio open circuit voltage (i.e. the voltage across the two terminals when RL is removed) and sum of load resistance and internal resistance of the network. It is given by Voc / (Ri + RL). 13. State Norton’s Theorem The Norton’s theorem explains the fact that there are two terminals and they are as follows: • One is terminal active network containing voltage sources • Another is the resistance that is viewed from the output terminals. The output terminals are equivalent to the constant source of current and it allows giving the parallel resistance. The Norton’s theorem also explains about the constant current that is equal to the current of the short circuit placed across the terminals. The parallel resistance of the network can be viewed from the open circuit terminals when all the voltage and current sources are removed and replaced by the internal resistance. 14. State Maximum power transfer theorem The Maximum power transfer theorem explains about the load that a resistance will extract from the network. This includes the maximum power from the network and in this case the load resistance is being is equal to the resistance of the network and it also allows the resistance to be equal to the resistance of the network. This resistance can be viewed by the output terminals and the energy sources can be removed by leaving the internal resistance behind.

MATHS ALL TRICKS AND TIPS

                              SARAL MATHS

FORE DOWNLOAD BOOK OF MATHS TRICKS AND TIPS WITH  ALL CHAPTER.

--------->>>>>>CLICK HERE<<<<<---------(260 PAGES)